Summary
Last update: Dec. 20, 2024
Details
- Note:
- Precautions for adding a new driver onto Windows Vista or later
Precautions for adding a new driver at Daylight Saving Time
| Title | Digital Electronics Corporation Memory Link Driver | ||||||||||||||||||||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Version | Ver. 1.19.14 | ||||||||||||||||||||||||||||||||||
| Supported Software | GP-Pro EX Ver2.10.000 or later | ||||||||||||||||||||||||||||||||||
| Supported Devices |
| ||||||||||||||||||||||||||||||||||
| Supported Units | Required versions depend on models. Please check "Supported Models / Version" for the required versions of GP-Pro EX. Required driver versions for different models are listed below.
| ||||||||||||||||||||||||||||||||||
| Device/PLC Connection Manual | For details, please read the "Device/PLC Connection Manual" in the lower part of this page. For general information regarding Device connection and documentation conventions please refer to "Device/PLC Connection Manual". | ||||||||||||||||||||||||||||||||||
| Updated Contents | [Ver. 1.9.14] （Dec. 20, 2024） The following issue was corrected:
|
How to install (This is a self-extracting file.)
- Prior to installation, be sure to close all software applications that are running.
-
- Click on the file name in the lower part of this page to start downloading the file.
- After download is complete, double-click on the downloaded file to start installation.
- Follow the instructions on the screen.
- After installation, start GP-Pro EX.
- Select [Digital Electronics Corporation] for "Manufacturer" and [Memory Link] for "Series" in [Device/PLC] settings of [System Settings] on the [Project] menu.
Terms of use / Cautions
Please acknowledge the following terms of use before you use our download service.Download of any file signifies your agreement to the terms of use.
Terms and conditions
Download file
Update History
[Ver. 1.9.14] （Dec. 20, 2024）
The following issue was corrected:- If on the ST6000, ET6000 series couldn't communicate with two-wire connection.
[Ver. 1.19.10]
The following settings were added:- Supported ST6000 series
[Ver. 1.18.10]
The following settings were added:- Supported USB-RS422/485 cable
[Ver. 1.15.08] (May. 25, 2009)
The following settings were added:- Supported ASCII / Chinese(Traditional) / Chinese(Simplified) / Korean fonts in Displaying a Character String Command(ESC T).
- Supported 16 hosts in TCP communication.
- Supported the connection limitation with Ethernet.
- Supported the indirection setting for Machine No. with extended mode [1:N ASCII] and [1:N binary] of Serial Communication.
- When using demand polling with TCP communication, display disconnect the TCP communication though time-out time for demand polling does not pass.
- When do not communicate during TCP communication more than one minute, TCP connection succeeds than other hosts. The display don't send the Interrupt Output on this occasion.
[Ver. 1.13.07] (Oct. 14, 2008)
The following issue was corrected:- There was the case that Display cannot shift to Offline or cannot transfer the project when use the Transaction Marker in the Ethernet communication.
[Ver. 1.13.06] (Apr. 25, 2008)
The following setting was added:- Transfer Timeout setting.
- When write to system area, display takes time till the value reflects in screen.
[Ver. 1.12.05] (Feb. 14, 2008)
The following issue was corrected:- When the expansion mode 1:1 ASCII and 1:1 binary is specified, GP doesn't reply to the host.
[Ver. 1.12.04] (Oct. 1, 2007)
The following setting was added:- Banner Message.
* Ver 2.10.000 or later version of GP-Pro EX are necessary to use Banner Message.
[Ver. 1.11.04] (Jun. 28, 2007)
The following settings were added:- Drawing command.
- Device Monitor.
* Ver 2.00.000 or later version of GP-Pro EX are necessary to use a Device Monitor.
[Ver. 1.10.04] (Mar. 26, 2007)
The following issue was corrected:- When a host keeps sending a command without waiting for the AGP response under the specific settings (Expansion mode 1:1 binary and 1:N binary), a format error (Error code: FC) occurs.
[Ver. 1.10.03] (Nov. 20, 2006)
The following issue was corrected:- When the expansion mode 1:1 ASCII and 1:1 binary is specified, the interrupt output data from GP is different from the one from GP2000.